Digital TSZ07 Owner's Manual

TSZ07 Tape DriveInstallation/Owner’s ManualOrder Number: EK–TSZ07–IN–003latigid

PrefaceThis manual provides the information needed to install and operate theTSZ07 Tape Drive.Structure of this ManualThe manual consists of the follo

Related Documentation• KZQSA Module Installation Guide (EK-KZSQA-IG)• MicroVAX Diagnostic Monitor User’s Guide (AA-FM7AE-DN)• TSZ07 Tape Drive Technic

ix

Für Bundesrepublik Deutschland und Berlin (West) For Federal Republicof Germany und West Berlin Pour la République féderale d’Allemagneet Berlin Ouest

KennzeichnungDie Geräte werden bereits in der Fertigung mit der Zulassungsnum-mer gekennzeichnet und mit einer Anmeldepostkarte versehen. SollteKennze

Figure 1: Models of TSZ07xii

Chapter 1Description1.1 IntroductionThis chapter contains a brief description of the TSZ07 Tape Drive.Figure 1 shows the available models.1.2 Descript

have a lower load reliability (85%) than the larger reels (98%) for ANSIcompatible tapes. Any reel with less than 600 feet of tape may require manuall

Chapter 2Installation2.1 IntroductionThis chapter explains how to unpack, install, and configure the tapedrive. There are three unpacking procedures:•

2.2 Site PreparationNo special site preparation is required, although peripherals operating inoffice areas can be affected by static discharge, tempera

If anything is missing, damaged, or incorrect, contact the dealer fromwhom the equipment was ordered.Remove any tape securing the front door (see Figu

2.3.2 Removing Packing Material from the TSZ07-CA, -FATo place the TSZ07 in the tape access position, perform the following:NOTEStep 1 applies to earl

2. Raise the top cover and place the cover retaining arm in the recessnext to the tape path. See Figure 2–3.Figure 2–3: TSZ07 Cover Retaining Arm - Ta

You can now remove the packing ring from the take-up hub.To close the table top TSZ07 enclosure, perform the following:1. Lift the cover retaining arm

CAUTIONSingle-ended and differential SCSI busses require differ-ent termination. Be sure to use the terminators marked"differential" with th

Figure 2–5: Typical Standalone SCSI Configurations DECstation 2100DECstation 3100DECstation 3100VAXstation 3100MicroVAX 3100 Q–bus BASEDVAXsystemKZQSAA

Figure 2–6: Typical Daisy Chained SCSI Configurations * INTERNAL SCSI BUS TERMINATOR (P/O SCSI MSC MODULE).** EXTERNAL SCSI BUS TERMINATORCS–8545D

Additional technical information on the interface and the connectors isavailable in the Module Installation Guide (see the Related Documenta-tion sect

2.4 Installing the Cabinet Models (TSZ07-BA/BB,-EA/EB)Installation of the Cabinet TSZ07 requires the following:1. Unpacking the TSZ07.2. Unpacking the

Figure 2–7: Cabinet Carton Removal2–12 Installation

TSZ07 Tape DriveInstallation/Owner’s ManualOrder Number: EK–TSZ07–IN–003Prepared byInformation Design and ConsultingDigital Equipment Corporation • Me

2.4.2 Tools and Working SpaceThe following tools are required for unpacking the cabinet model TSZ07.• Scissors• 9/16-inch wrench• 11/16-inch wrench• 3

2.4.3 Removing the TSZ07-BA/BB, -EA/EB from the CartonUse the following procedure to remove the cabinet model from the carton.WARNINGOnce the leveling

Figure 2–9: Unpacking Sequence3. Remove the metal hold-down brackets.Installation 2–15

4. Using a 11/16-inch wrench, loosen the leveling feet locking nuts (seeFigure 2–10).Figure 2–10: Raising Leveling Feet5. Using a 9/16-inch wrench, sc

2. Grasp the cabinet by the right top and left top (see Figure 2–11).Figure 2–11: Deskidding the CabinetInstallation 2–17

3. Roll the cabinet off of the skid and down the ramps, taking care toprevent it from tipping over.4. Open the rear door using a 5/32 inch hex key (se

2.4.5 Installing the Cabinet StabilizerThe cabinet model TSZ07 is shipped with a stabilizer in the top of thepacking carton. This stabilizer should be

8. Place lock washer and the rectangular washer on the 1/2 x 3/4 hexscrew and thread the screw into the coupler.9. Slide the shim into place.10. Level

Figure 2–13: Installing the Cabinet StabilizerInstallation 2–21

2.4.6 Remove Packing Material from the TSZ07-BA/BB, -EA/EBWhen you receive the TSZ07 there is a plastic ring on the take-up hub which must be removed

September 1992The information in this document is subject to change without notice and shouldnot be construed as a commitment by Digital Equipment Cor

Figure 2–14: Opening Cabinet LidInstallation 2–23

You can now remove the packing material from the take-up hub (seeFigure 2–3).To close the TSZ07 cabinet enclosure, perform the following:1. Lift the c

2.4.8 Unpacking the Small CartonOpen the accessories box and check its contents. The kit should containthe following:• TSZ07 Tape Drive Installation/O

2.5.1 Unpacking Rackmountable Models (TSZ07-AA, -DA)The rackmountable models are shipped in one large carton and onesmaller carton. The large carton c

Figure 2–15: TSZ07 Cover Retaining Arm - Rackmount ModelYou can now remove the packing ring from the take-up hub.To close the table top TSZ07 enclosur

2.5.3 Unpacking the Accessories CartonOpen the accessories carton and remove its contents. Check that the kitcontains the following:• TSZ07 Tape Drive

Figure 2–16: Rack Mounting the TSZ07HEX NUTSL BRACKETBAR NUTSLIDE RAILSFRONT OF CABINETREAR OF CABINETCS–9060SCREWSSLIDE RAILSBUTTON RELEASEBAR NUTSCR

6. Place the L bracket at the rear of the rails between the cabinetmounting rail and the slide rail.7. Install 2 screws and bar nut through the L brac

2.6 Running DiagnosticsAfter installing the TSZ07, run MicroVAX Diagnostic Monitor (MDM) onall systems where the TSZ07 is connected to a KZQSA. Select

2.6.3 Onboard DiagnosticsThe TSZ07 Tape Drive has high level onboard diagnostics. Thesediagnostics are activated through the front panel keys and the

Chapter 3Operation3.1 IntroductionThis chapter provides information on the operation of the TSZ07 asfollows:• A description of the controls and indica

3.2 Controls and IndicatorsExcept for the ac power switch which is located on the rear of the TSZ07,the controls and indicators are located on the fro

1. The five LED indicators over the control switches flash and thealphanumeric readout displays TESTING.2. The alphanumeric readout changes to TESTPASS

3.2.3 Alphanumeric DisplayAn eight-character alphanumeric display provides messages indicating:• Basic machine status• Tape density• Error conditions3

3.2.6 ONLINE (3) SwitchWith a tape loaded, the ONLINE (3) switch places the drive on-line andcauses the indicator above the switch to light. If the dr

3. Press the WRT EN/TEST (4) switch.4. Press the DENSITY SELECT (5) switch.5. Press the LOAD/REWIND (1) switch.6. Press the WRT EN/TEST (4) switch.7.

3.4.2 Host Density SelectionSelecting the operating density through the interface is a function of thehost system software and the interface itself.3.

Table 3–1: Activity MessageOperation MessagesDensity read ID (density)Density selected CMD (density)Erase fixed ERA(density)Erase security ERAS (densit

3. Make sure the tape is completely wound onto the reel, and, if youintend to write data to the tape, that a write-enable ring is installedon the reel

Figure 3–3: Inserting the Tape Reel5. Close the front door.6. Press the LOAD/REWIND switch. While loading, the Load/Rewindindicator flashes and the mes

ContentsPreface viiChapter 1 Description1.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–11.2 De

3.6.1 Manual Tape LoadingUse the following procedure to load tape manually. You may need to usethis procedure with six-inch tape reels.CAUTIONLifting

Figure 3–4: Location of the Manual Release Switch5. Thread the tape along the tape path shown in Figure 3–5.6. Move the packer arm away from the take-

Figure 3–5: Tape PathOperation 3–13

9. Press the LOAD/REWIND switch. While loading, the Load/Rewindindicator flashes and the message LOADING appears on the al-phanumeric display. The Writ

CAUTIONLifting the top cover whenever the tape drive ispowered on stops tape motion and prevents tapeloading or unloading, and could result in the los

3.7.1 Manual Unload of TapeUse the following procedure to manually unload the tape from the TSZ07.CAUTIONLifting the top cover whenever the TSZ07 is p

Table 3–2: Error MessagesMessages Problem/Action RequiredDoor ajar Close the front door.End of media Tape is full; another is required.Hub seat Verify

Chapter 4Preventive Maintenance4.1 IntroductionThis chapter explains how to perform all required preventive mainte-nance to the tape drive.CAUTIONIt i

4.2.1 Cleaning The Tape PathThe head of the TSZ07 should be cleaned every eight hours; the restof the tape path should be cleaned every 40 hours. Freo

2.4.5 Installing the Cabinet Stabilizer . . . . . . . . . . . . . . . . . . 2–192.4.6 Remove Packing Material from the TSZ07-BA/BB,-EA/EB . . . . . .

Figure 4–1: Tape Path and SensorsPreventive Maintenance 4–3

4.2.3 Air FilterThe air filter should be cleaned every six months. Remove the filterfrom the access hole in the front of the TSZ07 and clean it by blowi

Figure 4–2: Air FilterPreventive Maintenance 4–5

Appendix AAccessoriesA number of accessories are available for the TSZ07 Tape Drive, as listedin Table A-1.Table A–1: AccessoriesName Order NumberCrim

3.4.4 User Density Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–73.5 Activity Messages . . . . . . . . . . . . . . . . . . . . .

2–14 Opening Cabinet Lid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–232–15 TSZ07 Cover Retaining Arm - Rackmount Model . . . . . . 2–27